ASTM F3125-A490 - Boulons Plus

PLEASE NOTE:

The new F3125 specification is a consolidation and replacement of six ASTM standards, including; A325, A325M, A490, A490M, F1852, and F2280. Until the F3125 specification is more widely used and until the A325 and A490 specifications have been eliminated by ASTM, we will continue to manufacture and sell A325 and A490 heavy hex structural bolts under their existing specification requirements, unless F3125 is referenced in the inquiry and/or purchase order.

ASTM A490 (F3125)

Structural bolts, steel, heat treated, 150 ksi minimum tensile strength.

The ASTM A490 specification cover quenched and tempered, alloy steel, heavy hex structural bolts from 1/2″ diameter through 1-1/2″ diameter with a minimum 150 ksi tensile. These bolts are intended for use in structural connections and therefore have shorter thread lengths than standard hex bolts.

A490 bolts are similar in application and dimensions to A325 heavy hex structural bolts but are made from an alloy steel rather than a medium carbon steel, resulting in a higher strength fastener. The A490 specification is applicable to heavy hex structural bolts only.

For bolts with different thread lengths than specified for structural bolts but with similar mechanical properties, see Specification A354-BD. ASTM A490 bolts shall not be coated by hot-dip galvanizing, mechanical deposition, or electroplating with zinc due to the potential risk of hydrogen embrittlement. ASTM has approved coating A490 bolts with Zinc/Aluminum Corrosion Protective Coatings per ASTM F1136 Grade 3, commercially called dacromet and as per ASTM F2833, commercially called MAGNI 565. Additional testing in the form of Magnetic Particle Inspection for Longitudinal Discontinuities and Transverse Cracks is a requirement of the A490 specification.

FEATURES
Keg Weight
Meet ASTM Certifications
A2LA Certification
Traceable After Installed
All From Same Maker
Rocap Test Pass
Universal Skids
Keg Material
Easily Resealable
Handle On Keg
English Milltest
One Page Milltest
Free Taxes Canada/USA
Automated Milltest Sending

100% Domestic
All North American
$$$
200 Pounds
Metal

Mixed Set
Chinese Nuts
$$
95 Pounds
Plastic

100% Korean
All Korean Import
$
65 Pounds
Metal

Specifications

Types of A490 Bolts

Dimensions & Markings

Bolt Diam.	E	F			G		H			T
	Body Diam.	With Across Flat			With Across Corners		Head Height			Thread Length
	Max	Basic	Max	Min	Max	Min	Basic	Max	Min	Basic
1/2-13	0.515	7/8	0.875	0.850	1.010	0.969	5/16	0.323	0.302	1.00
5/8-11	0.642	1 1/16	1.062	1.031	1.227	1.175	25/64	0.403	0.378	1.25
3/4-10	0.768	1 1/4	1.250	1.212	1.443	1.383	15/32	0.483	0.455	1.38
7/8-9	0.895	1 7/16	1.438	1.394	1.660	1.589	35/64	0.563	0.531	1.50
1-8	1.022	1 5/8	1.625	1.575	1.876	1.796	39/64	0.627	0.591	1.75
1 1/8-7	1.149	1 13/16	1.812	1.756	2.093	2.002	11/16	0.718	0.658	2.00
1 1/4-7	1.277	2	2.00	1.938	2.309	2.209	25/32	0.813	0.749	2.00
1 3/8-6	1.404	2 3/16	2.188	2.119	2.526	2.416	27/32	0.878	0.810	2.25
1 1/2-6	1.531	2 3/8	2.375	2.300	2.742	2.622	15/16	0.974	0.902	2.25

F3125 Grade A490 Dimensions, Threads & Grade Marking
	Type 1	Type 3
Style Heavy Hex Bolts
Dimensions, ASME^B	B18,2,6	B18,2,6
Thread Fit, ASME^B	B1.1 UNC 2A	B1.1 UNC 2A
Grade Marking^{A, C}	A490	A490

^B Manufactured to the latest revision at the time of manufacture, UNC for inch series and Metric Coarse (MC) for Metric Series.
^C Previously used markings may be sold and used indefinitely, bolts must be manufactured to current marking requirements upon initial publication of this standard.

Source: The table above is inspired by Table 1 from the ASTM F3125 Standard that you can purchase on the ASTM Website

Grip Length

Grip Inches	Bolt Diameter Inches
Grip Inches	1/2	5/8	3/4	7/8	1	1 1/8	1 1/4	1 3/8	1 1/2
3/4	1 1/2	1 3/4	***	2	***	***	2 1/2	***	2 3/4
13/16	1 1/2	1 3/4	2	2	2 1/4	2 1/2	2 1/2	2 3/4	2 3/4
7/8	1 3/4	1 3/4	2	2	2 1/4	2 1/2	2 1/2	2 3/4	2 3/4
15/16	1 3/4	2	2	2 1/4	2 1/4	2 1/2	2 3/4	2 3/4	3
1	1 3/4	2	2	2 1/4	2 1/4	2 1/2	2 3/4	2 3/4	3
1 1/16	1 3/4	2	2 1/4	2 1/4	2 1/2	2 3/4	2 3/4	3	3
1 1/8	2	2	2 1/4	2 1/4	2 1/2	2 3/4	2 3/4	3	3
1 3/16	2	2 1/4	2 1/4	2 1/2	2 1/2	2 3/4	3	3	3 1/4
1 1/4	2	2 1/4	2 1/4	2 1/2	2 1/2	2 3/4	3	3	3 1/4
1 5/16	2	2 1/4	2 1/2	2 1/2	2 3/4	3	3	3 1/4	3 1/4
1 3/8	2 1/4	2 1/4	2 1/2	2 1/2	2 3/4	3	3	3 1/4	3 1/4
1 7/16	2 1/4	2 1/2	2 1/2	2 3/4	2 3/4	3	3 1/4	3 1/4	3 1/2
1 1/2	2 1/4	2 1/2	2 1/2	2 3/4	2 3/4	3	3 1/4	3 1/4	3 1/2
1 9/16	2 1/4	2 1/2	2 3/4	3 3/4	3	3 1/4	3 1/4	3 1/2	3 1/2
1 5/8	2 1/2	2 1/2	2 3/4	2 3/4	3	3 1/4	3 1/4	3 1/2	3 1/2
1 11/16	2 1/2	2 3/4	2 3/4	3	3	3 1/4	3 1/2	3 1/2	3 3/4
1 3/4	2 1/2	2 3/4	2 3/4	3	3	3 1/4	3 1/2	3 1/2	3 3/4
1 13/16	2 1/2	2 3/4	3	3	3 1/4	3 1/2	3 1/2	3 3/4	3 3/4
1 7/8	2 3/4	2 3/4	3	3	3 1/4	3 1/2	3 1/2	3 3/4	3 3/4
1 15/16	2 3/4	3	3	3 1/4	3 1/4	3 1/2	3 3/4	3 3/4	4
2	2 3/4	3	3	3 1/4	3 1/4	3 1/2	3 3/4	3 3/4	4
2 1/16	2 3/4	3	3 1/4	3 1/4	3 1/2	3 3/4	3 3/4	4	4
2 1/8	3	3	3 1/4	3 1/4	3 1/2	3 3/4	3 3/4	4	4
2 3/16	3	3 1/4	3 1/4	3 1/2	3 1/2	3 3/4	4	4	4 1/4
2 1/4	3	3 1/4	3 1/4	3 1/2	3 1/2	3 3/4	4	4	4 1/4
2 5/16	3	3 1/4	3 1/2	3 1/2	3 3/4	4	4	4 1/4	4 1/4
2 3/8	3 1/4	3 1/4	3 1/2	3 1/2	3 3/4	4	4	4 1/4	4 1/4
2 7/16	3 1/4	3 1/2	3 1/2	3 3/4	3 3/4	4	4 1/4	4 1/4	4 1/2
2 1/2	3 1/4	3 1/2	3 1/2	3 3/4	3 3/4	4	4 1/4	4 1/4	4 1/2
2 9/16	3 1/4	3 1/2	3 3/4	3 3/4	4	4 1/4	4 1/4	4 1/2	4 1/2
2 5/8	3 1/2	3 1/2	3 3/4	3 3/4	4	4 1/4	41/4	4 1/2	4 1/2
2 11/16	3 1/2	3 3/4	3 3/4	4	4	4 1/4	4 1/2	4 1/2	4 3/4
2 3/4	3 1/2	3 3/4	3 3/4	4	4	4 1/4	4 1/2	4 1/2	4 3/4
2 13/16	3 1/2	3 3/4	4	4	4 1/4	4 1/2	4 1/2	4 3/4	4 3/4
2 7/8	3 3/4	3 3/4	4	4	4 1/4	4 1/2	4 1/2	4 3/4	4 3/4
2 15/16	3 3/4	4	4	4 1/4	4 1/4	4 1/2	4 3/4	4 3/4	5
3	3 3/4	4	4	4 1/4	4 1/4	4 1/2	4 3/4	4 3/4	5
3 1/16	3 3/4	4	4 1/4	4 1/4	4 1/2	4 3/4	4 3/4	5	5
3 1/8	4	4	4 1/4	4 1/4	4 1/2	4 3/4	4 3/4	5	5
3 3/16	4	4 1/4	4 1/4	4 1/2	4 1/2	4 3/4	5	5	5 1/4
3 1/4	4	4 1/4	4 1/4	4 1/2	4 1/2	4 3/4	5	5	5 1/4
3 5/16	4	4 1/4	4 1/2	4 1/2	4 3/4	5	5	5 1/4	5 1/4
3 3/8	4 1/4	4 1/4	4 1/2	4 1/2	4 3/4	5	5	5 1/4	5 1/4
3 7/16	4 1/4	4 1/2	4 1/2	4 3/4	4 3/4	5	5 1/4	5 1/4	5 1/2
3 1/2	4 1/4	4 1/2	4 1/2	4 3/4	4 3/4	5	5 1/4	5 1/4	5 1/2
3 9/16	4 1/4	4 1/2	4 3/4	4 3/4	5	5 1/4	5 1/4	5 1/2	5 1/2
3 5/8	4 1/2	4 1/2	4 3/4	4 3/4	5	5 1/4	5 1/4	5 1/2	5 1/2
3 11/16	4 1/2	4 3/4	4 3/4	5	5	5 1/4	5 1/2	5 1/2	5 3/4
3 3/4	4 1/2	4 3/4	4 3/4	5	5	5 1/4	5 1/2	5 1/2	5 3/4
3 13/16	4 1/2	4 3/4	5	5	5 1/4	5 1/2	5 1/2	5 3/4	5 3/4
3 7/8	4 3/4	4 3/4	5	5	5 1/4	5 1/2	5 1/2	5 3/4	5 3/4
3 15/16	4 3/4	5	5	5 1/4	5 1/4	5 1/2	5 3/4	5 3/4	6
4	4 3/4	5	5	5 1/4	5 1/2	5 1/2	5 3/4	5 3/4	6
4 1/16	4 3/4	5	5 1/4	5 1/4	5 1/2	5 3/4	5 3/4	6	6

A325 STRUCTURAL BOLTS TYPE I
Boulons Plus offers ASTM A325 bolts type I as complete assemblies or bolts only.
Bolts are typically supplied as plain or hot dip galvanized, in diameters from 1/2” to 1-1/4” and lengths to 8”.
Fully threaded bolts are available, (thread to head, in lengths up to four times the diameter).
All of these bolts are heat treated to a minimum tensile strengh of 120 KSI up to 1” diameter, and 105 KSI over 1”.

A325 STRUCTURAL BOLTS TYPE III
ASTM A325 type III structural bolts are made of a special chemistry corrosion resistant, or weathering steel,
an alloy steel, containing copper, chromium and nickel. Type III fasteners are primarily used in outdoor structures.
As the surface of the steel corrodes, the type III material forms a fine-textured oxide coating. This oxide coating seals the surface of the base metal and appears to be a uniform fine grained, deep brown rust color.
Structural bolts in grade A325 type III all have mechanical properties identical to the standard fasteners properties.
Thus, type III structural fasteners can be substituted for standard structural fasteners.

A490 STRUCTURAL BOLTS TYPE I
ASTM A490 structural bolts type I are only supplied in plain (black) finish. These bolts are heat-treated to a tensile
strength range greater than 150 KSI. Medium carbon, alloy steel is used for these bolts.

All test results and suggestions are based on laboratory tests. Specific job site conditions should be taken into consideration when specifying the proper fastener. Because applications vary, we assume no liability for use of this information.

F3125 Grade A490-1 Chemical Properties

Chemical Requirements^C For ASTM F3125 Grade A490-1 & F2280-1 Bolts
Element	Alloy^D Steel with or Without Boron
Carbon	0.30 - 0.48^A
Manganese, min	0.60 min
Phosphorus Max	0.035
Sulfur Max	0.040
Silicon	^B
Boron	0.003 max
Copper	^B
Nickel	^B
Chromium	^B
Vanadium	^B
Molybdenum	^B
Titanium	^B

^ACarbon requirement is increased to 0.35-0.53 Heat analysis for 1 1⁄2 inch diameter bolts.
^B Not Specified.
^C Product analysis that is outside the specified range is permitted provided it is within 10% of the value required of the heat analysis. For example Heat analysis C 0.30-0.52 = Product analysis C 0.27-0.57 or Phosphorus max Heat analysis 0.040 = Product analysis 0.044.
^D Steel, as defined by the American Iron and Steel Institute, shall be considered to be alloy when the maximum of the range given for the content of alloying elements exceeds one or more of the following limits: Manganese, 1.65 %; silicon, 0.60 %; copper, 0.60 % or in which a definite range or a definite minimum quantity of any of the following elements is specified or required within the limits of the recognized field of constructional alloy steels: aluminum, chromium up to 3.99 %, cobalt, columbium, molybdenum, nickel, titanium, tungsten, vanadium, zirconium, or any other alloying elements added to obtain a desired alloying effect.

Source: The table above is inspired by Table 2 from the ASTM F3125 Standard that you can purchase on the ASTM Website

F3125 Grade A490-3 Chemical Properties

Chemical Requirements^C For ASTM F3125 Grade A490-3 & F2280-3 Bolts
Element	Based on Corrosion Index^E
Carbon	0.30 - 0.53 max
Manganese	0.60 min
Phosphorus Max	0.035
Sulfur Max	0.040
Silicon	^B
Boron	^B
Copper	0.20 - 0.60^E
Nickel	0.20^E,F min
Chromium	0.45^E min
Vanadium	^B
Molybdenum	0.10^E,F min
Titanium	^B

^B Not Specified.
^C Product analysis that is outside the specified range is permitted provided it is within 10% of the value required of the heat analysis. For example Heat analysis C 0.30-0.52 = Product analysis C 0.27-0.57 or Phosphorus max Heat analysis 0.040 = Product analysis 0.044.
^E Type 3 bolts conforming to Table 2, or Type 3 bolts which have a copper minimum Heat Analysis of 0.20% and a Corrosion Index of 6 or higher as calculated from the Heat Analysis as described in Guide G101 Predictive method based on the data of Larabee and and Coburn shall be accepted: I = 26.01 (% Cu) + 3.88 (% Ni) + 1.20 (% Cr) + 1.49 (% Si) + 17.28 (% P) – 7.29 (% Cu) (% Ni) – 9.10 (%Ni) (% P) – 33.39 (% Cu)2
^F Either Nickel or Molybdenum must be present in the amount specified.

Source: The table above is inspired by Table 2 from the ASTM F3125 Standard that you can purchase on the ASTM Website

Permitted Coating

PERMITTED COATING^H
	F2329^A	B695^A	F1136^E,G	F2833^F,G
Bolt	Hot-Dip Galvanized	Mechanically Deposited Zinc	Zinc/Aluminum	Zinc/Aluminum
A490	Not approved	Not approved	Grade 3	Grade 1
DIMENSIONAL LIMITS	BOLT PITCH DIAM.	BOLT PITCH DIAM.	BOLT PITCH DIAM.	BOLT PITCH DIAM.
	OS AFTER COATING^C,D	OS AFTER COATING^C	OS AFTER COATING^C	OS AFTER COATING^C
	IN.	IN.	IN.	IN.
1/2-13 UNC	Not Approved	Not Approved	0.006	0.006
5/8-11 UNC	Not Approved	Not Approved	0.007	0.007
3/4-10 UNC	Not Approved	Not Approved	0.007	0.007
7/8-9 UNC	Not Approved	Not Approved	0.008	0.008
1-8 UNC	Not Approved	Not Approved	0.008	0.008
1 1/8-7 UNC	Not Approved	Not Approved	0.008	0.008
1 1/4-7 UNC	Not Approved	Not Approved	0.008	0.008
1 3/8-6 UNC	Not Approved	Not Approved	0.010	0.010
1 1/2-6 UNC	Not Approved	Not Approved	0.0.10	0.010

^A Supplementary nut lubrication to A563 S1 is required for hot dip and mechanically deposited zinc coatings.
^C Bolt pitch oversize limit in case of dispute. Material within the plain gauge limits which meets the coating thickness requirements and assembles freely need not be
measured to this tolerance.
^D Hot-Dip galvanized is typically tapped after coating. Others coatings are typically applied after nut tapping.
^E Grade 5 of this coating meets the supplementary lubrication requirements of A563 S1.
^F Grade 1 of this coating meets the supplementary lubrication requirements of A563 S1.
^G Nuts overtapped for coating for use with 150 ksi/1040 MPa minimum tensile strength fasteners shall be proof load tested to a minimum of 175,000 psi after overtapping.
^H Other metallic and non-metallic coatings may be used on 120 ksi/830 MPa minimum tensile fasteners upon agreement between the purchaser and user. Performance
requirements shall be specified by the purchaser and agreed to in writing. Coatings for 150 ksi/1040 MPa bolts must be qualified.
OS = over-size
Source: The table above is inspired by Table A1.1 from the ASTM F3125 Standard that you can purchase on the ASTM Website

Tensile Strength Requirements

F3125 Grade A490 & F2280 TENSILE STRENGHT REQUIREMENTS FOR BOLTS TESTED FULL SIZE
	Stress Area^A	Tensile Min.	Tensile Max.	Proof Load^C Min.	Proof Load^D Min.
in.	in².	ft-lb	ft-lb	ft-lb	ft-lb
1/2-13	0.142 in².	21 300 ft-lb	24 600 ft-lb	17 050ft-lb	18 500 ft-lb
5/8-11	0.226 in².	33 900 ft-lb	39 100 ft-lb	27 100 ft-lb	29 400 ft-lb
3/4-10	0.334 in².	50 100 ft-lb	57 800ft-lb	40 100 ft-lb	43 400 ft-lb
7/8-9	0.462 in².	69 300 ft-lb	79 950 ft-lb	55 450 ft-lb	60 100 ft-lb
1-8	0.606 in².	90 900 ft-lb	104 850 ft-lb	72 700 ft-lb	78 800 ft-lb
1 1/8-7	0.763 in².	114 450 ft-lb	132 000 ft-lb	91 550 ft-lb	99 200 ft-lb
1 1/4-7	0.969 in².	145 350 ft-lb	167 650 ft-lb	116 300 ft-lb	126 000 ft-lb
1 3/8-6	1.155 in².	173 250 ft-lb	199 850 ft-lb	138 600 ft-lb	150 200 ft-lb
1 1/2-6	1.405 in².	210 750 ft-lb	243 100 ft-lb	168 600 ft-lb	182 600 ft-lb
Above Values Based On	*	150 000 psi	173 000 psi	120 000 psi	130 000 psi

^A The stress area is calculated as follows for inch: AS = 0.7854 [D – (0.9743/P)]2; for Metric: AS = 0.7854 (D – 0.9382P)2; where AS = Stress Area, D = Nominal Bolt Size, and P = thread pitch.
^C Proof load length measurement.
^D Alternative Proof load Yield Strength Method.

Source: The table above is inspired by Table 4 from the ASTM F3125 Standard that you can purchase on the ASTM Website

TENSILE STRENGHT REQUIREMENTS FOR SPECIMENS MACHINED BOLTS
F3125 Grade A490 & F2280	Tensile, min.	Tensile, max.	Yeld min,	Elong. in 4D, min. %	Red. of Area min. %
F3125 Grade A490 & F2280	150 000 Psi	173 000 psi	130 000 Psi	14	40

When the length of the bolt makes full-size testing impractical, machined specimens shall be tested and shall conform to the requirements specified in Table 5.

The table above is inspired by Table 5 from the ASTM F3125 Standard that you can purchase on the ASTM Website

Rotational Capacity

Connection Types

Matching Components

F3125 Grade A490 Matching Components
	Type 1	Type 3
Recommended Nut and Washer
Plain Nut	A563 DH	A563 DH3
Coated Nut	A563 DH	A563 DH3
Flat, Bevel or Thick washer if used	F436-1	F436-3

^E ASTM A194/A194M 2H heavy hex nuts may be used in place of A563 DH nuts on type 1 A325, A490, F1852 and F2280 bolts. When coated, the same requirements of A563 and this specification, and Annex A1, including overtap, coating, rotational capacity and proof load testing apply.

Source: The table above is inspired by Table 1 from the ASTM F3125 Standard that you can purchase on the ASTM Website

Hardness Requirements

HARDNESS REQUIREMENTS FOR F3125 GRADE A490 & F2280 BOLTS
		Brinell HB		Rockwell HRC
		Min	Max	Min	Max
Up to 1" INCLUSIVE	Less than 2D	311	352	33	38
Up to 1" INCLUSIVE	2D and longer	---	352	---	38
Over 1"	Less than 3D	311	352	33	38
Over 1"	3D and longer	---	352	---	38

10.2 Hardness:
10.2.1 Bolts shall conform to the hardness in Table 6. For
lots on which both hardness and tension tests are performed,
acceptance based on tensile requirements shall take precedence
in the event of low hardness readings.

Source: The table above is inspired by Table 6 from the ASTM F3125 Standard that you can purchase on the ASTM Website

Kegs & Skids Quantities

Diam. 5/8'' Keg Qty

DIAM: 5/8	FULL KEG*	HALF KEG	BOLTS/KEG	PER SKID INFOS
LENGTH	BOLTS/KEG	BOLTS/KEG	LBS/KEG	BOLTS/SKID	LBS/SKID
1 1/2	500	250	92.5	4,500	1,665
1 3/4	500	250	98	4,500	1,764
2	450	225	92.93	4,050	1,672.74
2 1/4	400	200	87.4	3,600	1,573.20
2 1/2	400	200	91.2	3,600	1,641.60
2 3/4	350	175	83.65	No Information	No Information
3	330	165	82.5	No Information	No Information
3 1/4	300	150	78.5	No Information	No Information
3 1/2	300	150	81.45	No Information	No Information
3 3/4	260	130	73.32	No Information	No Information
4	260	130	76.18	No Information	No Information
4 1/4	240	120	72.96	No Information	No Information
4 1/2	230	115	72.34	No Information	No Information
4 3/4	230	115	76.48	No Information	No Information
5	230	115	77.28	No Information	No Information
5 1/4	220	110	No Information	No Information	No Information
5 1/2	210	105	77.39	No Information	No Information
5 3/4	200	100	No Information	No Information	No Information
6	190	95	72.01	No Information	No Information

*Full Keg Sizes are for reference only. Boulons Plus only provide structural bolts in Half and third kegs sizes.
Kegs and skids weight is an approximation. The real weight may slightly differ from what is shown here.
Other Lenghts could be available upon request

Diam. 3/4'' Keg Qty

DIAM: 3/4	FULL KEG*	HALF KEG	BOLTS/KEG	PER SKID INFOS
LENGTH	BOLTS/KEG	BOLTS/KEG	LBS/KEG	BOLTS/SKID	LBS/SKID
1 1/2	340	170	96.39	3,060	1,735.02
1 3/4	300	150	89.7	2,700	1,529.82
2	300	150	93.75	2,700	1,593
2 1/4	270	135	89.24	2,430	1,606.23
2 1/2	260	130	89.96	2,340	1,619.28
2 3/4	250	125	90.38	2,250	1,843.65
3	230	115	86.71	2,070	1,560.78
3 1/4	220	110	86.35	1,980	1554.30
3 1/2	210	105	85.68	1,890	1,542.24
3 3/4	200	100	84.70	1,800	1,524.60
4	190	95	83.41	1,710	1,501.38
4 1/4	170	85	77.27	1,530	1390.77
4 1/2	170	85	79.90	1,530	1,438.20
4 3/4	150	75	72.9	1,350	1,312.20
5	150	75	75.23	1,350	1,354.05
5 1/4	130	65	67.21	1,170	1,209.78
5 1/2	130	65	69.23	1,170	1,246.05
5 3/4	130	65	71.18	1,170	1,155.60
6	130	65	73.13	1,170	1,316.25
6 1/4	120	60	No Information	1,080	No Information
6 1/2	120	60	71.10	1,080	1,279.80
6 3/4	110	55	No Information	No Information	No Information
7	110	55	69.20	990	1,242.45
7 1/4	No Information	No Information	No Information	No Information	No Information
7 1/2	100	50	65.75	900	1,148.85
7 3/4	No Information	No Information	No Information	No Information	No Information
8	90	45	61.88	810	1,113.75
8 1/4	No Information	No Information	No Information	No Information	No Information
8 1/2	85	40	58.76	810	1,189.89
8 3/4	No Information	No Information	No Information	No Information	No Information
9	80	35	53.52	No Information	No Information
9 1/4	No Information	No Information	No Information	No Information	No Information
9 1/2	70	30	47.73	No Information	No Information
9 3/4	No Information	No Information	No Information	No Information	No Information
10	60	25	41.33	540	826.20

Diam. 7/8'' Keg Qty

DIAM: 7/8	FULL KEG*	HALF KEG	BOLTS/KEG	PER SKID INFOS
LENGTH	BOLTS/KEG	BOLTS/KEG	LBS/KEG	BOLTS/SKID	LBS/SKID
1 3/4	220	110	97.9	No Information	No Information
2	200	100	93.2	1,800	1,589.94
2 1/4	190	95	92.53	1,710	1,665.54
2 1/2	180	90	91.53	1,620	1647.54
2 3/4	170	85	90.02	1,530	1,620.27
3	160	80	88.08	1,440	1,512
3 1/4	150	75	85.58	1,350	1,540.35
3 1/2	150	75	88.58	1,350	1,594.35
3 3/4	140	70	86.17	1,260	1,551.06
4	130	65	82.62	No Information	No Information
4 1/4	120	60	77.88	No Information	No Information
4 1/2	120	60	80.88	1,080	1,455.84
4 3/4	110	55	76.34	990	1,374.12
5	110	55	79.25	No Information	No Information
5 1/4	100	50	73.4	No Information	No Information
5 1/2	100	50	75.4	No Information	No Information
5 3/4	90	45	70.65	No Information	No Information
6	90	45	71.46	No Information	No Information

Diam. 1'' Keg Qty

DIAM: 1''	FULL KEG*	HALF KEG		PER SKID INFOS
LENGTH	BOLTS/KEG	BOLTS/KEG	LBS/KEG	BOLTS/SKID	LBS/SKID
2	150	75	105	No Information	No Information
2 1/4	140	70	93.31	1,260	1,764
2 1/2	140	70	97.51	1,260	1,679.58
2 3/4	130	65	93.80	1,170	1,688.31
3	130	65	97.70	1,170	1,758.51
3 1/4	120	60	93.18	1,080	1,677.24
3 1/2	110	55	88.17	990	1,586.97
3 3/4	110	55	91.47	990	1,646.37
4	100	50	85.65	900	1,541.70
4 1/4	90	45	76.95	810	1,385.10
4 1/2	90	45	82.04	810	1,476.63
4 3/4	85	45	84.74	810	1,525.23
5	85	45	88.335	810	1,590.03
5 1/4	80	40	82.40	No Information	No Information
5 1/2	80	40	82.12	No Information	No Information
5 3/4	70	35	75.95	No Information	No Information
6	35	35	75.71	No Information	No Information
6 1/2	35	35	79.56	No Information	No Information
7	60	30	71.49	No Information	No Information

*Full Keg Sizes are for reference only. Boulons Plus only provide structural bolts in Half and third kegs sizes. Kegs and
skids weight is an approximation. The real weight may slightly differ from what is shown here.
Other Lenghts could be available upon request

Diam. 1-1/8'' Keg Qty

DIAM: 1 1/8''	FULL KEG*	HALF KEG		PER SKID INFOS
LENGTH	BOLTS/KEG	BOLTS/KEG	LBS/KEG	BOLTS/SKID	LBS/SKID
2 3/4	100	50	91.50	No Information	No Information
3	95	50	99.50	No Information	No Information
3 1/4	85	45	92.70	No Information	No Information
3 1/2	80	40	85.20	No Information	No Information
3 3/4	80	40	88	No Information	No Information
4	75	40	90.80	No Information	No Information
4 1/4	70	35	81.90	No Information	No Information
4 1/2	70	35	84.35	No Information	No Information
4 3/4	65	35	86.80	No Information	No Information
5	65	30	76.50	No Information	No Information
5 1/4	55	30	78	No Information	No Information
5 1/2	50	25	83.75	No Information	No Information
5 3/4	50	25	92.50	No Information	No Information
6	50	25	70.75	No Information	No Information
6 1/2	45	25	74.25	No Information	No Information
7	45	25	77.75	No Information	No Information
7 1/2	40	20	65.06	No Information	No Information

Diam. 1-1/4'' Keg Qty

DIAM: 1 1/4''	FULL KEG*	HALF KEG		PER SKID INFOS
LENGTH	BOLTS/KEG	BOLTS/KEG	LBS/KEG	BOLTS/SKID	LBS/SKID
2 1/2	80	40	102	No Information	No Information
2 3/4	75	40	No Information	No Information	No Information
3	70	35	91	No Information	No Information
3 1/4	70	35	93.80	No Information	No Information
3 1/2	65	35	96.95	No Information	No Information
3 3/4	60	30	85.80	No Information	No Information
4	55	30	88.20	No Information	No Information
4 1/4	55	30	90.90	No Information	No Information
4 1/2	50	25	78	No Information	No Information
4 3/4	50	25	80	No Information	No Information
5	50	25	82.25	No Information	No Information
5 1/4	45	25	82.25	No Information	No Information
5 1/2	45	25	86.50	No Information	No Information
5 3/4	40	20	No Information	No Information	No Information
6	40	20	72.60	No Information	No Information

*Full Keg Sizes are for reference only. Boulons Plus only provide structural bolts in Half and third kegs sizes.

Kegs and skids weight is an approximation. The real weight may slightly differ from what is shown here.
Other Lenghts could be available upon request

Diam. 1-1/2'' Keg Qty

DIAM: 1 1/2''	FULL KEG*	HALF KEG		PER SKID INFOS
LENGTH	BOLTS/KEG	BOLTS/KEG	LBS/KEG	BOLTS/SKID	LBS/SKID
3 1/2	35	20	91.60	No Information	No Information
3 3/4	35	20	94.20	No Information	No Information
4	30	15	72.45	No Information	No Information
4 1/4	30	15	45.25	No Information	No Information
4 1/2	30	15	75.90	No Information	No Information
4 3/4	30	15	77.85	No Information	No Information
5	30	15	79.80	No Information	No Information
5 1/2	25	15	83.70	No Information	No Information
6	40	15	85.65	No Information	No Information
6 1/2	20	10	59.80	No Information	No Information

*Full Keg Sizes are for reference only. Boulons Plus only provide structural bolts in Half and third kegs sizes.

Kegs and skids weight is an approximation. The real weight may slightly differ from what is shown here.
Other Lenghts could be available upon request

Quantity

Other Sizes are available upon request. We can manufacture custom length and thread as long as it respect the A490 standards. Contact us to get a quotation.

Buy the ASTM F3125 Standard

TYPES OF F3125 GRADE A490 BOLTS
TYPE 1	Medium carbon and alloy steel. (STANDARD)
TYPE 2	Withdrawn in 2002.
TYPE 3	Weathering steel.
M	Metric A490.

CONNECTION TYPES
SC	Slip critical connection.
N	Bearing type connection with threads included in the shear plane.
X	Bearing-type connection with threads excluded from the shear plane.

PLEASE NOTE:

ASTM A490 (F3125)

Structural bolts, steel, heat treated, 150 ksi minimum tensile strength.

FEATURES

100% Domestic

All North American

$$$

Mixed Set

Chinese Nuts

$$

100% Korean

All Korean Import

$

Specifications

Kegs & Skids Quantities

Quantity

Back To Home Page